In modern buildings with tight shells, often room-independent air supply is required for proper operation of biomass stoves. One possibility to arrange this supply is to use a double-wall chimney with flue gas leaving through the pipe and fresh air entering through the annular gap. A one-dimensional quasi-static model based on balance equations has been developed and compared with experimental data. Inclusion of leak air is crucial for reproduction of the experimental results. © 2014, Springer-Verlag Berlin Heidelberg.

Biochar is the product of biomass pyrolysis and gasification. One of the possible application of this product is certainly in agronomic sector, as soil amendment. However biochar use in Italy is subordinated to insert this product in fertilizer list, which biochar could be commercialized with. The aim of this paper is to know the biochar from gasification process (using an Imbert downdraft prototype), in particular investigating its potentiality as soil amendment in terms of European and Italian regulations and in terms of physical and chemical characterizations.

Wood pellets have been reported to emit toxic gaseous emissions during transport and storage. Carbon monoxide (CO) emission, due to the high toxicity of the gas and the possibility of it being present at high levels, is the most imminent threat to be considered before entering a pellet storage facility. For small-scale (<30 tons storage capacity) residential pellet storage facilities, ventilation, preferably natural ventilation utilizing already existing openings, has become the most favored solution to overcome the problem of high CO concentrations. However, there is little knowledge on the ventilation rates that can be reached and thus on the effectiveness of such measures. The aim of the study was to investigate ventilation rates for a specific small-scale pellet storage system depending on characteristic temperature differences. Furthermore, the influence of the implementation of a chimney and the influence of cross-ventilation on the ventilation rates were investigated. The air exchange rates observed in the experiments ranged between close to zero and up to 8 m³h^-1, depending largely on the existing temperature differences and the existence of cross-ventilation. The results demonstrate that implementing natural ventilation is a possible measure to enhance safety from CO emissions, but not one without limitations. © 2014 © The Author 2014. Published by Oxford University Press on behalf of the British Occupational Hygiene Society.

Adsorptive on-board desulfurization units require a high desulfurization and regeneration performance for a wide range of fuels to keep them small and ensure long maintenance intervals. A novel thermal regeneration strategy was investigated in this work, fulfilling all requirements for in situ on-board regeneration. In this strategy, a temperature-controlled flow rate (TCFR) of air was used to control the temperature inside the adsorber. With this dynamic approach, the regeneration time was reduced significantly in comparison to other thermal regeneration strategies. The novel regeneration strategy was tested using Ag–Al₂O₃ as an adsorbent to desulfurize a benzothiophen (BT)-enriched road diesel (300 ppmw of total sulfur). A commercial diesel containing fatty acid methyl ester (FAME) was used to evaluate the fuel flexibility regarding desulfurization and regeneration performance. In the case of 6.63 wt % FAME and 300 ppmw of sulfur, the breakthrough adsorption capacity of sulfur decreased from 1.04 to 0.17 mg/g. In TCFR regeneration experiments, the breakthrough adsorption capacity was restored to over 94% in the case of both fuels. Thereby, the Brunauer–Emmett–Teller (BET) surface area of the regenerated adsorbent decreased by only 1.5%, and negligible carbon deposits were detected.

Nowadays prefabricated houses are becoming increasingly popular, thanks to their low cost and high energy performance. Heating systems installed in these houses should be carefully designed and controlled, to ensure sufficient thermal comfort while maintaining low fuel consumptions. This study presents the simulation of different system configurations and control strategies for a pre-fabricated house, located in Lower Austria. The house is heated by a 6 kW pellet boiler directly connected to a floor heating system, in a configuration without buffer storage tank. Using the TRNSYS simulation suite, a coupled simulation of the house and its heating and hot water supply system was set up, calibrated and validated with reference to monitoring data. As monitoring data evidenced that the control strategy of the heating system is not ideal to maintain a comfortable indoor temperature during the whole day, two improved strategies were simulated over the heating season and evaluated in terms of thermal comfort, pellet consumption and boiler’s efficiency. Moreover, to better understand the influence of the system configuration, simulations have been repeated considering another heat distribution system (radiators instead of floor heating). Results show that the radiators’ network, if adequately controlled, reduces by 85% the total discomfort time. In addition, the pellet boiler mainly operates in load modulation regime, leading to lower pellet supply rates and therefore to lower pellet consumptions (18% less than floor heating). However, the lower operational loads and frequent ignitions result in a slightly lower efficiency of the pellet boiler (4% less than the configuration with floor heating.

Biochars produced from pelletized grape vine (GV) and sunflower husk (SFH) agricultural residues were studied by pyrolysis in a batch reactor at 400 and 500 °C. Chemical and physical evolution of the biomass under pyrolysis conditions was determined and the products were characterized, including the main gaseous organic components. Results showed a decrease in solid biochar yield with increasing temperature. Biochar is defined as a “porous carbonaceous solid” produced by thermochemical conversion of organic materials in an oxygen depleted atmosphere, which has physiochemical properties suitable for the safe and long-term storage of carbon in the environment and, potentially, soil improvement. The aim of this work is to improve the knowledge and acceptability of alternative use of the biochar gained from agro-forestry biomass residuals, such as grape vine and sunflower husks, by means of modern chemical and physical characterization tools.

The dual fluidized bed (DFB) steam gasification technology of biomass was developed at Vienna University of Technology and is well-established for transforming biomass into a product gas which can be used for further applications. The DFB steam gasification reactor consists of a gasification chamber (bubbling bed, fluidized with steam) and a combustion chamber (turbulent bed, fluidized with air). Biomass is fed into the gasification chamber and gets in contact with the bed material, typically Olivine, at about 840°C. The released volatiles leave the gasification reactor as product gas. A part of the solid residue, called char, flows with the bed material via a chute to the combustion chamber where it is burnt with air. The bed material is heated up, separated from the flue gas stream in a cyclone and flows back to the gasification reactor via a loop seal where it provides the heat for devolatilization and drying of the biomass. The movement of the char is crucial since a sufficient amount has to flow to the combustion chamber and burn to provide enough energy for bed material heat-up. Up to now little is known about the char concentration in the bed material recirculation stream (or short recirculation stream) and its influencing variables. Therefore, a cold flow model, operated with ambient air, was constructed to study the influence of various parameters on the char concentration in the recirculation stream. Bronze is used as bed material since is matches closest to the scaling criteria. The char is also scaled; polyethylene is used as model char.

The cold flow model, see Figure 1 for the flowsheet, consists of a “gasification chamber” which corresponds to the gasification chamber in the hot plant and is as well operated as a bubbling bed. Via a chute the recirculation stream moves to a rotary valve which enables to set a fixed recirculation rate and make it independent from the following pneumatic conveying. Then, gas and solids are separated in a cyclone and the recirculation stream finally flows back to the gasification chamber. After the loop seal samples are taken for investigation of the model char concentration in the recirculation stream. In the present study the influence of fluidization rate in the gasification chamber, bed material recirculation rate and model char mass in the system on the char concentration in the recirculation stream are investigated. It was found that the model char particles show a flotsam behavior. Higher fluidization rates increase the model char concentration in the recirculation stream because of better mixing, whereas the bed material recirculation rate has only little influence. Doubling and tripling the overall char mass in the system did not lead to a doubling or tripling model char concentration in the recirculation stream. The present observations are helping to better understand the ongoing phenomena inside of the dual fluidized bed gasification reactor and provide knowledge to further optimize it.

Ash related problems such as slagging, fouling, and high temperature corrosion in biomass fired boilers are still insufficiently explored due to the complexity of the underlying processes. High temperature corrosion of low alloy steels like 13CrMo4-5 has already been investigated in plants firing chemically untreated wood chips. In this earlier work it has been suggested that the oxidation of the steel is the dominating mechanism in the material temperature range between 450 and 550 °C. Unfortunately the exponential dependence of the material degradation on the flue gas temperature also found within this work cannot be explained with the proposed corrosion mechanism. To determine the dominating corrosion mechanism, additionally test runs have been carried out in a specially designed drop tube reactor. To investigate the time-dependent corrosion behavior of 13CrMo4-5, a newly developed mass loss probe was applied under several constant parameter setups. In addition to these measurements, the time-dependent oxidation of 13CrMo4-5 under air was investigated in a muffle furnace. To gain relevant information regarding the corrosion mechanism prevailing, the deposits as well as the corrosion products have been examined subsequently to the test runs by means of scanning electron microscopy and energy dispersive X-ray analyses. With the experimental data gained it could be shown that the dominating corrosion mechanism strongly depends on the conditions prevailing (e.g., steel temperature, flue gas temperature, and velocity) and can either be the oxidation of the steel by gaseous O₂ and H₂O or a combination of oxidation and active Cl-induced oxidation.

In this paper, the activity of a cobalt/molybdenum (Co/Mo) commercial catalyst for the Water Gas Shift Reaction for hydrogen production was investigated in a three fixed-bed reactor pilot plant using a tar-rich synthesis gas from a full-scale biomass gasification plant as feed-stream. A parametric variation study was carried out to assess CO conversion (X_CO) and selectivity for the water gas shift reaction as a function of the operating temperature (T) in the range 300–450 °C. The effects of four dry gas hourly space velocities (GHSV), Case A-Case D, two steam to dry synthesis gas ratios (H₂O/SG), 56% v/v and 67% v/v, and a H₂S concentration in the range 100–220 ppm_v,db were investigated: the highest CO conversion (∼95%) was observed in the base case (Case A GHSV) at 67% v/v H₂O/SG, and 450 °C, the lower the operating temperature the lower the CO concentration, the lower the gas hourly space velocity the higher the CO conversion and the higher the H₂O/SG the higher the CO conversion. The effect of H₂S variation on CO conversion was also studied, keeping the operating temperature constant (≈365 °C) and using the Case D GHSV: CO conversion increased as the H₂S concentration increased and X_CO ≈ 40%. Selectivity was not influenced by the parameters investigated. Finally, the effect of the catalyst on tar removal was studied and a CO conversion close to 85% was found.

The crucial point in inorganic particle formation from biomass combustion is the temperature-dependent release of inorganic compounds, especially potassium (K). Currently, common wood fuels comprise of a comparatively low amount of K, but the increased usage of wood energy requires new feedstocks in the future. Potentially new feedstocks, such as short rotation coppice (SRC), fuels from agriculture (e.g., straw), or wood from broad-leafed trees of low rotation, contain usually high ash contents and/or high K concentrations. Apparently, these feedstocks will cause increased inorganic particle emissions from biomass combustion processes. The principle of a decreased firebed temperature as a primary measure aiming at a retention of K in the ashes of the firebed is a common approach for particle emission reduction and was investigated in several previous studies. The present study describes the usage of an ash-rich fuel from SRC pellets made from willow in a residential pellet boiler modified with an unique prototype of direct water-based firebed cooling. This test setup enables the study of the isolated impact of decreased firebed temperatures and its influence on the combustion process and emissions as well. A statistically significant effect of the firebed cooling on temperatures below the burner plate as on gaseous HCl and SO₂ was found. The high ash content of the used fuel limited the effectiveness of the applied direct firebed cooling in residential biomass combustion. The accumulation of a thick and thermal insulating ash layer above the burner plate decreased the heat transfer, limited the cooling efficiency, and revealed deviations from the expected particle formation process.

Utilization of biomass as feedstock in dual fluidized bed steam gasification is a promising technology for the substitution of fossil energy carriers. Experience from industrial scale power plants showed an alteration of the olivine bed material due to interaction with biomass ash components. This change results mainly in the formation of Ca-rich layers on the bed particles. In this paper, a mechanism for layer formation is proposed and compared to the better understood mechanism for layer formation on quartz bed particles. Olivine bed material was sampled at an industrial scale power plant before the start of operation and at pre-defined times after the operation had commenced. Therefore, time dependent layer formation in industrial-scale conditions could be investigated. The proposed mechanism suggests that the interaction between wood biomass ash and olivine bed particles is based on a solid-solid substitution reaction, where Ca2+ is incorporated into the crystal structure. As a consequence Fe2+/3+ and Mg2+ ions are expelled as oxides. This substitution results in the formation of cracks in the particle layer due to a volume expansion in the crystal structure once Ca2+ is incorporated. The results of this work are compared to relevant published results including those related to quartz bed particles.
 

Conceptual solution of production of pure renewable hydrogen from wood gas or product derived from the commercial biomass steam gasification plant Güssing, Austria was carried out. The proposed process of product gas upgrading consisted of tree basic operations: (I) catalyzed water-gas shift (WGS) reaction, (II) gas drying and cleaning in a wet scrubber and (III) hydrogen purification by pressure swing adsorption. The tail gas or adsorbate can be used like fuel for gas engine for electrical energy production or like a boiler fuel for hot water-heat production.

To gain better insight into inorganic element release processes, test runs with a specially designed single particle reactor connected with an inductively coupled plasma mass spectrometer (ICP-MS) have been performed. Relevant combustion related parameters such as mass loss during thermal degradation, temperature development of the particle (surface and center), and composition of released gases were recorded. By coupling the reactor to an ICP-MS, time-resolved release profiles of relevant aerosol forming elements (S, Cl, K, Na, Zn, and Pb) were determined. Targeted and controlled interruptions of the experiments (quenching) after a certain time were performed to validate reactor performance and reliability of the measurements. Test runs with softwood and straw pellets (8 mm in diameter and about 20 mm in length) were performed at reactor temperatures of 700, 850, and 1000 °C under oxidizing conditions (5.6 or 4.2 vol % O₂). These test runs have revealed that the release ratios of volatile and semivolatile ash forming elements (S, Cl, K, Na, Zn, and Pb) generally increase as reactor temperatures rise. Moreover, regarding straw, higher Si and Al contents influence the release behavior of K, Na, Zn, and Pb. For K, existing release mechanisms proposed in the literature have been confirmed, and for Na it has been suggested that release mechanisms similar to K prevail. Especially during the starting phase of the experiment, a distinct temperature gradient exists from the surface to the center of the particle. Thus, different conversion phases occur in parallel in different layers of the particle, which has to be considered during the interpretation of the time-resolved release profiles of the main inorganic elements. Furthermore, transport limitations due to the occurrence of molten phases (especially for straw at reactor temperatures of 1000 °C) were obvious and could be directly derived from the online recorded release profiles. The targeted interruption of the ongoing decomposition process (quenching) provided an indication of the validity of the release profiles for S, K, Na, Zn, and Pb. Additionally, these experiments delivered valuable information regarding possible release mechanisms.

The phenomenon of off-gassing from wood pellets during storage has been the cause of several, in some cases fatal, accidents due to toxic atmospheres in storages. To optimize safety measures the nature of the responsible processes needs to be clarified. In this study the impact of O₂ availability, which is a decisive factor for the presumed oxidation of fatty acids, is pointed out. Off-gassing rates of CO, CO₂, VOC, and CH₄ of pellets at relatively constant O₂ levels of approximately 35%, 20%, and <1% over a period of 20 d at approximately 295 K were investigated. For this purpose 7 kg of spruce pellets was stored under simulated ventilation of the atmosphere in a 31 L tank. Gas concentrations were determined every 24 h by GC-FID/TCD. Compared to the mean emission rates at 35% O₂ of CO (0.22 mg kg^–1pellets_d.b. in 24 h) and CO₂ (0.76 mg kg^–1pellets_d.b. in 24 h) the lowest O₂ concentration of <1% resulted in a significant reduction of off-gassing rates of 40% for both gases. In contrast the release rates of VOCs and also CH₄ decreased with the higher O₂ concentration (0.035 to 0.025 mg kg^–1pellets_d.b. in 24 h; 0.0085 to 0.0061 mg kg^–1pellets_d.b. in 24 h), presumably, because of increased onward reactions to CO and CO₂. Since off-gassing was not prevented by the lack of O₂ (<1% O₂-trial) it is assumed that the O₂ required for the reactions originated from the biomass itself. During the storage of pellets at 20% O_2, emission rates of CO (0.18 mg kg^–1pellets_d.b. in 24 h) and CO₂ (0.79 mg kg^–1pellets_d.b. in 24 h) at the start decreased by more than 20% and those for VOCs (0.032 mg kg^–1pellets_d.b. in 24 h) by almost 30% after 3 weeks. It can be assumed that in ventilated storages the reactivity and thus a potential risk from off-gases from wood pellets decreases considerably in only a few weeks. The effects of aging, in terms of declining reactivity at relatively constant tank conditions, on off-gassing rates could be clarified for the first time. A realistic development of the decline of reactivity of the material itself could be determined.

This paper presents the virtual biomass grate furnace, which comprises of comprehensive CFD models of all relevant processes for the simulation of biomass grate furnaces. The models consist of a 3D packed bed model, a gas phase combustion model for laminar to highly turbulent flows and a model to account for the influence of the flue gas streaks arising from the fuel bed in the freeboard. The simulation results of a 20 kW underfeed stoker furnace show that the overall CFD model is able to provide valuable insight on the processes occurring in the packed bed and freeboard and their interactions.

The use of biomass as feedstock for gasification is a promising way of producing not only electricity and heat but also fuels for transportation and synthetic chemicals. Dual fluid bed steam gasification has proven to be suitable for this purpose. Olivine is currently the most commonly used bed material in this process due to its good agglomeration performance and its catalytic effectiveness in the reduction of biomass tars. However as olivine contains heavy metals such as nickel and chromium no further usage of the nutrient-rich ash is possible and additional operational costs arise due to necessary disposal of the ash fractions. This paper investigates possible alternative bed materials and their suitability for dual fluid bed gasification systems focusing on the behavior of the naturally occurring minerals olivine, quartz and K-feldspar in terms of agglomeration and fractionation at typical temperatures. To this end samples of bed materials with layer formation on their particles were collected at the industrial biomass combined heat and power (CHP) plant in Senden, Germany, which uses olivine as the bed material and woody biomass as feedstock. The low cost logging residue feedstock contains mineral impurities such as quartz and K-feldspar which become mixed into the fluidized bed during operation. Using experimental analysis and thermochemical it was found that the layers on olivine and K-feldspar showed a significantly lower agglomeration tendency than quartz. Significant fractionation of particles or their layers could be detected for olivine and quartz, whereas K-feldspar layers were characterized by a higher stability. High catalytic activity is predicted for all three minerals once Ca-rich particle layers are fully developed. However quartz may be less active during the build-up of the layers due to lower amounts of Ca in the initial layer formation.
 

Wood pellets have been used in domestic heating appliances for three decades. However, because the share of renewable energy for heating will likely rise over the next several years, alternative biomass fuels, such as short-rotation coppice or energy crops, will be utilized. We tested particulate emissions from the combustion of standard softwood pellets and three alternative pellets (poplar, Miscanthus sp., and wheat straw) for their ability to induce inflammatory, cytotoxic, and genotoxic responses in a mouse macrophage cell line. Our results showed clear differences in the chemical composition of the emissions, which was reflected in the toxicological effects. Standard softwood and straw pellet combustion resulted in the lowest PM₁ mass emissions. Miscanthus sp. and poplar combustion emissions were approximately three times higher. Emissions from the herbaceous biomass pellets contained higher amounts of chloride and organic carbon than the emissions from standard softwood pellet combustion. Additionally, the emissions of the poplar pellet combustion contained the highest concentration of metals. The emissions from the biomass alternatives caused significantly higher genotoxicity than the emissions from the standard softwood pellets. Moreover, straw pellet emissions caused higher inflammation than the other samples. Regarding cytotoxicity, the differences between the samples were smaller. Relative toxicity was generally highest for the poplar and Miscanthus sp. samples, as their emission factors were much higher. Thus, in addition to possible technical problems, alternative pellet materials may cause higher emissions and toxicity. The long-term use of alternative fuels in residential-scale appliances will require technological developments in both burners and filtration.

The study investigates for the first time the possibility of using carbon rich paper recovery sludge, and nitrogen rich meat processing industry waste as cultivation medium for the production of high value enzymes needed in the respective industries. The complex cellulose rich deinking sludge was able to support the growth of many industrially relevant enzyme producing microorganisms (Bacillus licheniformis, Candida cylindracea, Aspergillus oryzae, Trichoderma reesei) and of recombinant enzyme producers (Escherichia coli and Pichia pastoris). Further detailed studies with Trichoderma reesei as model organism demonstrated that the organism was able to grow optimally in the presence of 40gL-1 paper sludge as carbon source and 67.5 gL-1 pasteurised blood as nitrogen source substituted in Mandels medium. Under these conditions cellulase activities up to 28.1 nkat FPU were achieved. Anyhow, to achieve these results pretreatment of both waste streams is inevitable. In summary, this study provides the practical basis for a valorisation systems of paper industry waste to produce valuable enzymes to be used on-site in paper processing or for other purposes.

Detailed reaction schemes and experimental data for the online release of pyrolysis volatiles are required to gain a more fundamental understanding of biomass pyrolysis, which would in turn allow the process to be controlled in a more precise way and the development of more targeted applications. A detailed online characterisation of pyrolysis products has been conducted in single particle experiments with spruce pellets at different temperatures, obtaining a good closure of the elemental mass balances. The yields and online release of CO, CO₂, H₂O, CH₄, other light hydrocarbons and total organic condensable species, as well as char yield and composition, can be predicted with a reasonable accuracy with the application of a single particle model, coupled with a detailed pyrolysis scheme, and a simple one-step scheme for tar cracking. In order to achieve it, improvements have been conducted in the pyrolysis scheme, mainly concerning the release of light hydrocarbons and char yield and composition. Deviations are still present in the different groups in which organic condensable species can be classified.

The syngas mixture produced from biomass (bio-syngas) is characterized by a H2/CO molar ratio of 1.5 in this work, which is different from that of traditional syngas ratio of 2. Therefore a hybrid of winddiesel technology with bio-syngas conversion by Fischer–Tropsch synthesis (WD-FT) on a cobalt based catalyst was investigated, for the first time, using a slurry reactor. The result from feeding this technology is compared with the direct converting biomass derived synthetic gas to fuels via Fischer–Tropsch synthesis (BS-FT). Experiments were performed at different syngas composition (variation of H2/CO ratio), keeping the other parameters (temperature 230 °C; gas flow 5 Nm³/h, pressure 20 bar) constant. Comparison of the WD-FT with the BS-FT synthesis results displayed mass fraction of light hydrocarbons and higher catalytic stability and activity after 500 h. The olefin structures for the different product distributions, obtained from different reactions, are determined by ¹H NMR spectroscopy. Negligible amounts of iso-α-olefins were detected in the product of the WD-FT reaction. In the case of the alpha value, a slight change was observed between 0.93 and 0.92 for the BS-FT and WD-FT reaction.
 

In this work a novel reaction mechanism for gas phase reactions has been developed to predict the formation of aromatic compounds from the pyrolysis products of woody biomass particles. The aromatic compounds are important for being main soot precursors as well as their toxic properties. The developed gas phase mechanism is validated with experimental data from literature as well as experimental data performed with a single particle reactor for three different pyrolysis temperatures, namely 550, 800 and 1000°C. A good agreement is achieved between model results and experimental data for the total yield of each main family of aromatic hydrocarbons, i.e. phenolics, BTXs and PAHs.

Adsorptive desulfurization is a promising technology to provide sulfur free fuels for fuel cell based power units. In this work the adsorption kinetics of three different aromatic sulfur heterocycles was studied for Ag-Al₂O₃. The influence of individual as well as competitive adsorption on the selectivity order was investigated by equilibrium and breakthrough experiments. In these experiments a jet-A1 fuel enriched with benzothiophene (BT), dibenzothiophene (DBT), and 4,6-dimethyldibenzothiophene (4,6-DMDBT) was used. The adsorption of aromatic sulfur heterocycles on Ag-Al₂O₃ proceeds via three different adsorption mechanisms. Within these mechanisms the π-interaction (π-Ag) and the direct sulfur-silver interaction (S-Ag) are significantly stronger in comparison to the acid base interaction (S-H). The results showed that the π-Ag and S-Ag interactions are the major adsorption mechanisms in the first stage, where film-diffusion limits the adsorption rate. In the second stage, the S-H interaction plays only an important role for BT, where intraparticle diffusion is the rate controlling step. The overall selectivity order was found to be BT > DBT > 4,6-DMDBT in the case of competitive adsorption for both equilibrium and breakthrough performance. The S-H contribution was related to incorporation of silver into blank γ-alumina, which significantly increased the overall acidity of the adsorbent.

Substitution of fossil fuels for production of electricity, heat, fuels for transportation and chemicals can be realized using biomass steam gasification in a dual fluidized bed (DFB).

Interaction between biomass ash and bed material in a fluidized bed leads to transformation of the bed particle due to enrichment of components from the biomass ash resulting in the development of ash layers on the bed particle surface. These ash-rich particle layers enhance the catalytic activity of the bed material regarding the water-gas-shift reaction and the reduction of tars.

The water-gas-shift reaction at conditions typical for dual fluidized bed biomass gasification at a temperature of 870 °C was investigated. Diffusion and heat transfer limitations were minimized using a lab-scale experimental set-up consisting of a gas mixing section and a quartz glass reactor in which the catalyst is investigated.

Thermochemical conversion of biomass feedstock via dual fluidized bed steam gasification is a well-proven technology used to produce a medium calorific product gas for various applications in the energy or transportation sector or for chemical syntheses. At unfavorable gasification conditions, undesirable high amounts of tar, which are aromatic hydrocarbons, are present in the product gas. High tar contents are a major problem, and they lead to uneconomic operation due to sharply diminished quality of product gas or unexpected plant shut downs due to fouling of the product gas coolers. Currently, tar content is measured with a discontinuous wet-chemical analysis method, which needs several hours of sample preparation to receive the final tar content. The aim of this study is to establish valid correlations between online measured permanent gas components in the product gas and its tar content. The results show that hydrogen, methane, and ethene concentrations are strongly related to the tar content in the product gas, while the carbon monoxide and carbon dioxide content did not show a clear correlation. Using these correlations with online measured gas components provides the possibility of a direct and prompt response of a plant operator in case of unfavorable gasification conditions. Additionally, an optimization of the plant operation can be conducted and thereby, the operation hours and, consequently, the economic efficiency are improved.

This study presents combustion behavior and emission results obtained for different fuels: poultry litter (PL) and its char (PLC), scrap tires (ST) and its char (STC) and blends of char/lignite (PLC/LIG and STC/LIG). The combustion parameters and emissions were investigated via a non-isothermal thermogravimetric method and experiments in a lab-scale reactor. Fuel indexes were used for the prediction of high temperature corrosion risks and slagging potentials of the fuels used. The addition of chars to lignite caused a lowering of the combustion reactivity (anti-synergistic effect). There was a linear correlation between the NO_x emissions and the N content of the fuel. The form of S and the concentrations of alkali metals in the fuel had a strong effect on the extent of SO₂ emissions. The use of PL and PLC in blends reduced SO₂ emissions and sulphur compounds in the fly ash. The 2S/Cl ratio in the fuel showed that only PLC and STC/PLC would show a risk of corrosion during combustion. The ratio of basic to acidic oxides in fuel indicated that ST, STC and STC/LIG have low slagging potential. The molar (Si + P + K)/(Ca + Mg) ratio, which was used for PL, PLC and PLC containing blends, showed that the ash melting temperatures of these fuels would be higher than 1000 °C.

The CO/CO₂ release ratio obtained during char combustion of single biomass particles has been analysed in this work experimentally and by modelling. Experiments have been conducted with spruce, straw and Miscanthus pellets at different temperatures. Furthermore, these experiments have been modelled with a single particle model coupled with a CFD model of the single particle reactor. The results show that the CO/CO₂ ratio strongly depends on the feedstock, being lower for spruce than for straw or Miscanthus. Furthermore, the most commonly employed correlations for this ratio in literature are not adequate, as they either under- or over-predict it.

Dual fluidized bed (DFB) systems for biomass gasification consist of two connected fluidized beds with a circulating bed material in between. Inside such reactor systems, rough conditions occur due to the high temperatures and the movement of the bed material. Computational fluid dynamics calculations are a useful tool for investigating fluid dynamics inside such a reactor system. In this study, an industrial-sized DFB system was simulated with the commercial code CPFD Barracuda. The DFB system is part of the combined heat and power (CHP) plant at Güssing, situated in Austria, and has a total fuel input of 8 MW_th. The model was set up according to geometry and operating data which allows a realistic description of the hot system in the simulation environment. Furthermore, a conversion model for the biomass particles was implemented which covers the drying and devolatilization processes. Homogeneous and heterogeneous reactions were considered. Since drag models have an important influence on fluidization behavior, four drag models were tested. It was found that the EMMS drag model fits best, with an error of below 20%, whereas the other drag models produced much larger errors. Based on this drag law, further simulations were conducted. The simulation model correctly predicts the different fluidization regimes and pressure drops in the reactor system. It is also able to predict the compositions of the product and flue gas, as well as the temperatures inside the reactor, with reasonable accuracy. Due to the results obtained, Barracuda seems suitable for further investigations regarding the fluid mechanics of such reactors.

Firewood roomheaters are popular, widespread and important for reaching European CO₂ emission targets. Since they contribute significantly to local air pollution, they have to be optimized towards minimal emission release, especially in real-life operation. Draught conditions and user behavior, particularly the ignition technique, significantly affect the emission and efficiency performance of firewood roomheaters. This study assessed the effects of the respective parameters experimentally. The results revealed a clear correlation between draught conditions and thermal efficiency. Increased draught conditions up to 48 Pa significantly decreased thermal efficiency by 6%–11% absolutely. However, for gaseous emissions no clear trend was observed. Accordingly, CO and OGC emissions increased at higher draught conditions for one tested roomheater by 30% and 60%, but decreased for two other tested roomheaters by 13%–45%. For PM emissions no effect of increased draught conditions was evident. Top-down ignition technique did not lead to a significant decrease of PM emissions compared to bottom-up ignition. In contrast, bottom-up ignition led to best thermal efficiencies. The use of either spruce or beech as kindling material revealed no significant relevance for the ignition performance.

This study analyses the emission factors of two firewood room heaters under testing conditions which emulate real life operation. A 6.5 kW stove with low heat storage capacity and high leakage rate (stove A) is compared with an 8 kW air-tight stove with high heat storage capacity (stove B). Thermal efficiency, carbon monoxide (CO) and organic gaseous compound (OGC) emissions, as well as the thermal heat losses (THL) during cool down phase were investigated in a series of laboratory tests. Furthermore, the influence of closing the air supply dampers at the end of the heating cycle was evaluated. Test results for the whole test cycle (including cool down phase) showed that stove A had CO emissions of 2633 mg/MJ_Output and OGC emissions of 203 mg/MJ_Output, while stove B had CO emissions of 2408 mg/MJ_Output and OGC emissions of 109 mg/MJ_Output, when air dampers were closed. It was also found that user behaviour has a critical influence on the stoves’ performance. Closing the air supply dampers at the end of the stove operation improved the efficiency by up to 5.0 percentage points. Furthermore, the duration of the cool down phase increased, as well as CO and OGC emissions decreased. As a matter of fact, measures to improve the user behaviour as for example user trainings and accurate manuals are of major importance in order to decrease emissions and increase efficiency of domestic heating appliances. Moreover, real life emission factors of other technologies should be established in order to develop a database which can be applied in air quality dispersion models.

Diffusion coefficients of various solutes in supercritical water, which were either measured or retrieved from Molecular Dynamics simulations, were reviewed. Diffusion coefficients of molecules relevant for supercritical water processes were calculated with correlations reported in the literature and compared to the values of reference data. For conditions well above the critical point of water the simple Stokes-Einstein equation predicts the diffusion coefficients with an accuracy better than 20%. For conditions near the critical point the Wilke-Chang correlation gives the most accurate results. Diffusion coefficients for typical molecules occurring in supercritical water processes such as O2, N2, CO, CO2, or CH4 are estimated to be in the range of 60 · 10⁻⁹ m²/s at 673 K and 30 MPa. For H2, for which no experimental data are available, much higher diffusion coefficients in the range of 250 · 10⁻⁹ m²/s seem plausible. The data set of binary diffusion coefficients in supercritical water, either determined experimentally or by Molecular Dynamics simulations, should be extended significantly to include more solutes, as well as higher temperatures and pressures.
 

In order to evaluate the combustion behaviour of new biomass feedstocks such as short rotation coppice (poplar wood chips), fuels from agriculture (wheat straw pellets) and biomass residues (maize spindle grits), comprehensive test runs investigating both particulate matter (PM) and gaseous emissions were performed. A commercially available small-scale biomass boiler, especially designed to enable high fuel flexibility, was used for this evaluation. The combustion behaviour was determined for various boiler load conditions and primary air ratios while maintaining a constant total air ratio. Based on wet chemical analyses of the fuels, fuel indexes were calculated to deliver primary information on the combustion behaviour to be expected. During the test runs appropriate operating conditions were determined for these new biomass feedstocks in order to optimise combustion parameters and to minimise PM and gaseous emissions as well as to inhibit ash related problems (slagging, ash deposit formation and corrosion). The optimisation of operating conditions by primary measures showed a big potential for a stable boiler operation combined with reduced emissions. The findings provide the basis for a further development of combustion systems as well as control systems for the combustion of new biomass feedstocks.